2018 Ninja 400 “Superbike” ;)

2018 Ninja 400 “Superbike”. Bike has been a race / track bike since new. Clean title in hand. Fresh motor just built from 2019 salvage bike (I have that title as well). See motor build list below. Over 4k spent on motor alone, only 1 round raced on new motor with CRA at Podium Club in April this year. I have built and sold many 400s over the last four years and know these bikes very well, all are still on the track and going strong. I don’t sell junk. Buy it for the asking price and I’ll include Woodcraft Tire warmers, front and rear stands, new rain tires, and an AIM Solo 2 lap timer. If you are local, I’ll also pit for you at a local track day and help you get it adjusted and set for you.

I also have 2 more nearly identical builds one will be listed soon and is ready to go now, the other will be available at the end of the ASMA racing season. We are selling as we are moving to Aprilia RS660s next year, we have are bikes and need to fund the builds.

$10,000 OBO


· CRC Bodywork

- Minor low-side repair still looks great for “race bike” quality.

· MSS Performance Lightweight Upper Faring Stay

· Tyga Keyless Gas Cap

· eBay Double Bubble Windscreen

· Ohlins STX36 Rear Shock with 110 Spring

· Andreani Fork Cartridge with 1.0 springs

· Tapered Roller Bearing Steering Head Bearings

· Woodcraft Clip-ons 2.5" Rise

· Brake and Clutch Lever Guards

· Domino Kill/Start Switch

· New Domino Grips

· CRG Brake Front Lever

· Norton Racing Race Spec Throttle Kit

- Very short throw, shorter than the shortest Motion Pro wheel.

· SV Racing Parts Front Brake Spacer

· Woodcraft Key Switch Delete

· ZETA Adjustable Clutch Lever and Perch

- Changes the leverage point for longer moment of engagement for better starts.

· Spears Straight Clutch Cable

· Spears Stainless Steel Braided Front Brake Line no Banjo at Caliper

· Brembo SuperSport 310mm Front Rotor

· Vesrah VD-446 RJL ZZ Front Brake Pads

· Woodcraft Rear-Sets

· Annitori Quickshifter PRO 2

· Fast Franks Captive Rear Caliper

· Braided Rear Brake Line

· Woodcraft Rear Master Heavy Return Spring

· DID ERT3 Chain

· 520 Lightweight Drilled Front Sprocket

· 520 Aluminum Rear Sprocket

· Spears Chain Guard Shark Fin

· Spears Aluminum Side Stand Delete Bracket

· Radiator Guard

· 1.6 Bar High Pressure Radiatior Cap

· Motion Pro Coolant Recovery Tank

· Heat Shield / Thermal Deflector

· Regulator Relocation Bracket

· Lithium Battery

Engine

· Spears 2mm Big Bore Kit

· Arizona Sportbike Development Head

· Norton Racing Cylinder Coolant Seal

· SMOG Block off plates

· Spears High Pressure Oil Pump Relief Spring

· Ninja400R Race Spec Clutch Upgrade Kit

- Clutch Cable Spring Kit

- Blueprinted Shift Change Shaft and Protection Spacer

- Heavy Duty Barnett Clutch Friction Plates with Extra Wide Plate (Judder Spring Delete)

- Barnett Heavy Duty Clutch Springs

- Heavy Duty Shift Detent Spring

- Race Spec Shift Star

- 2020 Pull Rod & Bearing

· Spears Aluminum Core/Rubber Bonded 3 Piece Gasket Kit

· "GB" Case Covers (eBay Version)

· MWR Air Filter

· Norton Velocity Stacks

· Spears Aluminum Fuel Injection Supply Pipe

· Hindle Full Exhaust with DB Killer

· Woolich ECU Tune

 

Bump, make me an offer. Would like to get this one as well as the two other similar builds sold so I can start building our 660s.

 

Where are you located please?

 

Bike is located in Mesa, AZ

 

Thanks Mr. Dirt

 

Please call me. I am very interested in your 400. If you are in AZ can we meet at Chuck. I live in San Diego. I have license at CVMA, AFM and WERA. Thanks Travis 760-822-8616

 

This bike is still available. I sold one of the three we have (all similar builds) and will be delivering it to Chuckwalla this Friday (10/6). I can bring this bike with me if anyone has interest in checking it out. Make me an offer would like to get this sold soon to continue with our RS660 builds.

 

Sold! We do have one more with the same build that will be available in a few weeks.

 

What are you looking to get for the last one?