1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

YZ450F Supermono Project

Discussion in 'Bikes for Sale' started by swiest152, Jun 7, 2020.

  1. swiest152

    swiest152 Zoran's headache

    450 supermono project that I've lost interest in now that race season has started.

    2010-2013 YZ450F Frame modified to fit a two stroke engine. Wouldn't be too hard to get it back to fitting a yz450f engine.

    JGR Aluminum Fuel tank (originally made for James Stewart and then Justin Brayton )
    Braced Swingarm
    Marchesini Rear wheel
    Ohlins TTX Shock
    RS125 Tail
    Subframe modified to fit the tail.
    TZ250 tank cover (and spare)
    MotoForza ER6 Fairings(upper and lower)
    Fairing stay and brackets to work with Fairings
    Rearset plates tacked to frame
    ValterMoto Rearsets w/ Carbon heel guards
    MishiMoto Radiators and hoses

    $1900 with JGR Fuel Tank
    $1600 with out JGR Fuel Tank

    Located in Ephrata, PA

    I also have a Magnesium Marchesini front rim (for GSXR) I can include for an extra $500

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
    geoduch and SoCal1000 like this.
  2. E Reed

    E Reed Well-Known Member

    Do you have a front end for it?
     
  3. swiest152

    swiest152 Zoran's headache

    I do not.
     
  4. E Reed

    E Reed Well-Known Member

    I have a 13 YZ450. I'm assuming that the stock triples and forks would fit, would just have to play around with fork length I guess.

    I'm definitely interested. Just need to think it through a little bit. Are you going to be at the next Road America round and would you have room to haul it there? I live just a couple miles from Parrish and I'll see if he'll haul it back from there for me.
     
  5. swiest152

    swiest152 Zoran's headache

    Stock front end will bolt up. missing bottom bearing race.

    I will be there and could probably squeeze it in.
     
    geoduch likes this.
  6. Kurlon

    Kurlon Well-Known Member

    Lots and LOTS of years of Yamaha dirty bike front ends will bolt right up. My 1992 WR250ZD is sporting a 2009 YZ450 front end including clamps, Yamaha really only played around with steering stem length over the years, ODs / bearings are the same, and when in doubt, you can just press new stems into old clamps and vice versa.
     
    E Reed likes this.
  7. swiest152

    swiest152 Zoran's headache

    $1700 with the JGR gas tank.
     
  8. SPATT

    SPATT In a gravel pit near you

    I think I want this. Text me
     
  9. swiest152

    swiest152 Zoran's headache

    Can you handle it?
     
  10. regularguy

    regularguy Always Krispy

    oh hell....
     
    JJJerry likes this.
  11. 90kacoupe

    90kacoupe Novice seeking Help

    What two stroke engine was it setup for??
     
  12. t500racer

    t500racer Never Fails To Fail

    :stupid: What he said...
     
  13. swiest152

    swiest152 Zoran's headache

    LT500.

    The important mod was adding room for the exhaust to go through the middle of the frame which should make this easy to adapt any 2t engine.
     
  14. Monsterdood

    Monsterdood Well-Known Member

    :rolleyes:
     
  15. pjdibbini

    pjdibbini Well-Known Member

    this gone?
     
  16. swiest152

    swiest152 Zoran's headache

    Still have it.
     
  17. swiest152

    swiest152 Zoran's headache

  18. Rawb

    Rawb Member

    Sent a PM.
     

Share This Page