1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

2K7 GSXR 750 PART OUT

Discussion in 'Parts for Sale' started by MoeFaux, Aug 17, 2019.

  1. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Location: Grand Rapids, MI

    Bike: 2007 GSXR GSXR 750

    Story: the bike seems to have a crack allowing coolant to drain into the oil, so the engine is not viable as a whole. Want parts off the motor that aren't listed? Make an offer! Want the whole motor to dissect on your own? Make an offer! Want parts I don't have listed like sensors, frame, harnesses, swingarm, etc? Make an offer! All prices are before shipping, unless noted TYD.

    Suspension:

    • 500 - Penske triple clicker. Currently sprung for 180 lbs. Due for service.
    • 450 - Front forks with 30 mm extensions and Traxxion Dynamic internals. Sprung for 180 lbs. Due for service
    • 50 - Springs for forks above for 220 lbs.

    Electronics:
    • 600 - Bazzaz with QS and TC. The knob for adjusting TC is broken. Can be replaced for $40. QS is set up for GP.
    • 150 - Gauge cluster, stock

    Brakes:
    • 200 - Brembo RCS19 master cylinder. Can include reservoir and mounting bracket
    • 475 - Brembo Monobloc calipers
    • 130 - Vesrah SS brake pads for monobloc above. NIB. Retail $150 TYD
    • 50 - Brake pads for stock GSXR 750 calipers. NIB. DP racing compound. TYD
    • 50 - Braided lines for front brakes
    • 50 - Rear brake, stock. Full assembly

    Controls:
    • 90 - Woodcraft clip-ons. Three handle tubes included, two have the slider and some of the bar ground down from lowsides. Still fully functional. Sold
    • 65 - Motion Pro throttle. 1st gen.
    • 30- Stock throttle/switch assembly
    • 300 - Scott's Steering Dampener
    • 180 - Woodcraft rearsets. Some grinding of the left peg. Aesthetic damage only.SOLD
    • 35 - Clutch perch, lever, cable
    • 10 - Clutch lever, stock

    Wheels:

    • 300 - front and rear set, both with rotors. Wave rotor on rear. Black
    • 300 - front and rear set, both with rotors. Wave rotor on rear. Black
    • 30 - cush drive

    Body, Tank:
    60 - Hotbodies tailpiece. In decent shape. Pics on request.
    180- Gas tank. Prestine
    100 - Fuel pump. Can include with gas tank above.
    35 - Woodcraft frame sliders. Two rights, one left. Black. Prestine.
    30 - Zero Gravity Windshield





     
    Last edited: Aug 17, 2019
  2. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Also for sale:

    400 - M4 full exhaust. good sized dent in the can. Pics upon request.
     
  3. Joedirt1

    Joedirt1 Well-Known Member

    Pics of tank please 219-916-4045. Thanks
     
  4. sicc

    sicc Well-Known Member

    Pics please. 206 999 0683
     
  5. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Pics of tank, for your viewing pleasure.

    Plastic cover took some abuse, but all the metal is cherry.

    The keyed gas cap and matching cylinder/key can also be included.[​IMG][​IMG][​IMG]

    Sent from my Pixel using Tapatalk
     
  6. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Pics of the M4 can. Everything not pictured is used but undamaged. No surprises there.[​IMG][​IMG][​IMG]

    Sent from my Pixel using Tapatalk
     
  7. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Pics of the tail piece. Note cracks on the right rear. All bolt holes are intact.[​IMG][​IMG][​IMG]

    Sent from my Pixel using Tapatalk
     
  8. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Correction - further research indicates that you need $130 if you want to replace both the map selector switch and the TC adjustment knob that were damaged. The unit is sold new without these for $780. Let's reduce the price to $550 for the unit, and I'll include the perch ($30 retail) for the switches.
     
  9. MoeFaux

    MoeFaux Knee Puck Enthusiast

    One set of rims and cush drive sold. Set #2 still available.
     
  10. Sb polo

    Sb polo Well-Known Member

    SHIPPING COST FOR THE TAIL SECTION?
     
  11. MoeFaux

    MoeFaux Knee Puck Enthusiast

    I just quoted shipping to someone in Louisiana, and it was going to be $46 from Michigan.

    Sent from my Pixel using Tapatalk
     
  12. Sb polo

    Sb polo Well-Known Member

    i am in Detroit maybe we can work out local pickup if shipping is expensive
     
  13. MoeFaux

    MoeFaux Knee Puck Enthusiast

    I'll PM[​IMG]

    Sent from my Pixel using Tapatalk
     
  14. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Brembo master cylinder and braided lines sold.

    Sent from my Pixel using Tapatalk
     
  15. MoeFaux

    MoeFaux Knee Puck Enthusiast

    Scratch that. Deal fell through. I still have both rim sets and the cush drive / sprocket carrier available.

    Sent from my Pixel using Tapatalk
     
  16. tracknoob5

    tracknoob5 Member

    Can you email me an invoice on Paypal for the Tank shipped to 15904?
     
  17. tracknoob5

    tracknoob5 Member

    I also need a subframe as well if you have one
     
  18. cbush

    cbush Well-Known Member

    Which model Brembo monoblocks?
     
  19. MoeFaux

    MoeFaux Knee Puck Enthusiast

    I can't claim to know enough to answer this well. Previous owner told me they were OEM from a later model GSXR 1000. Pic below shows B024 embossed on the body. Does that answer the question?[​IMG]

    Sent from my Pixel using Tapatalk
     
  20. SPL170db

    SPL170db Trackday winner

    Yes those are the OEM Brembos that came on 2011 and later 600/750 and 2012 and later 1000's.....different color variations here and there, but same basic model underneath


    [​IMG]
     
    MoeFaux likes this.

Share This Page