gotime25
05-25-2009, 03:17 AM
2005 Honda CR85RBrr
Located in Athens, AL
list of mods:
ENGINE:
Complete engine re-build, balanced/blueprinted
Hot Rod Crank assy.
Wiseco piston (std. bore)
AllBalls crank bearings and seals
all O.E.M. bearings and seals through out
Ported and polished
transfers matched from cyl. to cases
Stock cyl. head and Milled head also, both come with bike
Hinson Billet clutch basket
New O.E.M. clutch fibers/ stiffer clutch springs
New CV4 red hoses
FUEL/AIR/ELECTRICAL:
PWK28 Carb. (polished) bored 1mm over/ jetted for U4.2 all new internals
V-Force 3 Reed valve
K&N Air filter
Vortex 10 map adjustable ignition
Pro Circuit complete exhaust w/R304 silencer (new packing)
SUSPENSION/WHEELS/BRAKES:
17' Excel wheels 2.50 front, 3.50 rear
Dunlop GP125 slicks (new)
Buchannon SS spokes
New stock hubs painted black to match frame
EBC oversized rotor (front)
Brand new EBC MXS pads
450r dual piston caliper
Goodridge SS brake line
Brembo Master cylinder
Shortened front forks with Racetech valves set-up for 170lb. rider w/ heavy springs
Stock rear shock re-valved and sprung for 170lb. rider
New shock linkage
CHASSIS:
Stock chassis painted black
New All balls steering stem bearings
Big Wheel swing arm with new bushings
New Acerbis black plastic
Pro Taper CR High bars (new)
Moose barkbusters
Sunline Clutch lever
Sunline Shift lever
EXTRA'S:
Mis. gaskets, seals, bearings
small wheel swing arm
extra set of plastics (red, stated above)
extra Renthal handlebars
extra 52mm cylinder, cylinder head, piston
STD. bore cyl. head and milled head (stated above)
14t, 15t, 16t counter shaft sprockets
49t, 50t, 51t rear sprockets
stock front brake (lever, line, mater cyl., caliper)
stock wave rotor (front)
stock crank (still good!)
stock springs (front and rear)
2 stock CDI's
mis. nuts and bolts
CR85 shop manual
$3,600
The engine was built by Ronnie Thompson of RPM of Huntsville. I am pretty sure i have missed a few things but you get the point, if you buy the bike anything else i find for the CR goes with it. I bought the bike, stripped it down and basically completely re-built the bike using everything in the above list, the bike only has 3 hours on it since the re-build. Due to finances and lack of time do not have time to enjoy this bike, THIS IS MY LOSS AND YOUR GAIN. I am willing to ship the bike at your exspense and can work with the price if needed be. This bike is safety wired and ready to race. If interested you can contact me either through email (bamaboy2high23@yahoo.com) or by phone @ 256-497-4498 (please no calls after 10pm CST) I am willing to meet within reasonable distance and can possibly have the bike delivered to some WERA events in my area. Thanks for looking.
Courtney
Located in Athens, AL
list of mods:
ENGINE:
Complete engine re-build, balanced/blueprinted
Hot Rod Crank assy.
Wiseco piston (std. bore)
AllBalls crank bearings and seals
all O.E.M. bearings and seals through out
Ported and polished
transfers matched from cyl. to cases
Stock cyl. head and Milled head also, both come with bike
Hinson Billet clutch basket
New O.E.M. clutch fibers/ stiffer clutch springs
New CV4 red hoses
FUEL/AIR/ELECTRICAL:
PWK28 Carb. (polished) bored 1mm over/ jetted for U4.2 all new internals
V-Force 3 Reed valve
K&N Air filter
Vortex 10 map adjustable ignition
Pro Circuit complete exhaust w/R304 silencer (new packing)
SUSPENSION/WHEELS/BRAKES:
17' Excel wheels 2.50 front, 3.50 rear
Dunlop GP125 slicks (new)
Buchannon SS spokes
New stock hubs painted black to match frame
EBC oversized rotor (front)
Brand new EBC MXS pads
450r dual piston caliper
Goodridge SS brake line
Brembo Master cylinder
Shortened front forks with Racetech valves set-up for 170lb. rider w/ heavy springs
Stock rear shock re-valved and sprung for 170lb. rider
New shock linkage
CHASSIS:
Stock chassis painted black
New All balls steering stem bearings
Big Wheel swing arm with new bushings
New Acerbis black plastic
Pro Taper CR High bars (new)
Moose barkbusters
Sunline Clutch lever
Sunline Shift lever
EXTRA'S:
Mis. gaskets, seals, bearings
small wheel swing arm
extra set of plastics (red, stated above)
extra Renthal handlebars
extra 52mm cylinder, cylinder head, piston
STD. bore cyl. head and milled head (stated above)
14t, 15t, 16t counter shaft sprockets
49t, 50t, 51t rear sprockets
stock front brake (lever, line, mater cyl., caliper)
stock wave rotor (front)
stock crank (still good!)
stock springs (front and rear)
2 stock CDI's
mis. nuts and bolts
CR85 shop manual
$3,600
The engine was built by Ronnie Thompson of RPM of Huntsville. I am pretty sure i have missed a few things but you get the point, if you buy the bike anything else i find for the CR goes with it. I bought the bike, stripped it down and basically completely re-built the bike using everything in the above list, the bike only has 3 hours on it since the re-build. Due to finances and lack of time do not have time to enjoy this bike, THIS IS MY LOSS AND YOUR GAIN. I am willing to ship the bike at your exspense and can work with the price if needed be. This bike is safety wired and ready to race. If interested you can contact me either through email (bamaboy2high23@yahoo.com) or by phone @ 256-497-4498 (please no calls after 10pm CST) I am willing to meet within reasonable distance and can possibly have the bike delivered to some WERA events in my area. Thanks for looking.
Courtney