liquid_iq
04-05-2008, 10:07 PM
Not going to be racing this season and can't let this sweet bike sit around. This is Rob Jensen's AMA Supersport 05 R6. The next owner was Greg Melka. It was sold to Ronnie who never rode it and two weeks later sold it to me. It is this bike (http://forums.13x.com/showthread.php?t=145392&highlight=melka). Since then it has been repainted and a few miscellaneous parts replaced because I'm a perfectionist.
It also has a new STM slipper clutch with one track day and four races on it.
Bike is in MINT condition and ready to race.
DynoJet PCIII and quick shifter
New injectors, mapped by Kinetic for MR9 but runs fine on U4 or pump gas
Engine has milled head and one layer out of head gasket
STM Slipper clutch (new friction disks and plates were installed also)
Graves throttle body slide stops
Ohlins steering dampner
T-man built 25mm Ohlins fork kit (.95 springs), GMD optimized
Ohlins rear shock - 600lb shock spring
Steel brake lines front/rear
520 RK chain,Vortex sprockets
EBC brakes
Sharkfin chain guard
Graves flat peg rearsets
Vortex clip ons
Graves Fairing stay
Sharkskinz plastic (repaired and in great shape)
YEC kit ECU (15,900 rev limit-lots of tuning adjustments, temp in speedo)
YEC kit air filter
Modified fuel pump allows tank drain from quick-disconnect fitting
Vortex fuel cap
Vortex frame sliders with shorty pucks & swingarm spools
Vortex Case cover (left)
Factory Pro case cover (right)
Hindle full system with TI can
WERA/CCS safety wired
Stomp-grip
CCS transponder pouch under tail
Michelin PR-3 rear with two sprint races on it
Michelin PR-C front with not much more laps than the rear
Included with the bike are some miscellaneous spares - clip on bars, complete clutch, stock air filter, extra exhaust cans/midpipe, levers, etc.
Available spares include complete set of wheels/rotors/sprocket with Michelin rain tires (slightly used), matching fuel tank complete with cap and pump (no stomp-grip though), matching tail (repaired), air box, new EBC Laser Cut race pads for front, etc.
Bike is located just North of Tampa, FL.
http://www.liquidiq.com/ebay/r6_left.jpg
http://www.liquidiq.com/ebay/r6_front_left.jpg
http://www.liquidiq.com/ebay/r6_front_right.jpg
http://www.liquidiq.com/ebay/r6_right.jpg
http://www.liquidiq.com/ebay/r6_lower_left.jpg
http://www.liquidiq.com/ebay/r6_lower_left_rear.jpg
http://www.liquidiq.com/ebay/r6_right_rear.jpg
http://www.liquidiq.com/ebay/r6_right_lower_rear.jpg
http://www.liquidiq.com/ebay/r6_right_lower_front.jpg
http://www.liquidiq.com/ebay/r6_dash_running.jpg
It also has a new STM slipper clutch with one track day and four races on it.
Bike is in MINT condition and ready to race.
DynoJet PCIII and quick shifter
New injectors, mapped by Kinetic for MR9 but runs fine on U4 or pump gas
Engine has milled head and one layer out of head gasket
STM Slipper clutch (new friction disks and plates were installed also)
Graves throttle body slide stops
Ohlins steering dampner
T-man built 25mm Ohlins fork kit (.95 springs), GMD optimized
Ohlins rear shock - 600lb shock spring
Steel brake lines front/rear
520 RK chain,Vortex sprockets
EBC brakes
Sharkfin chain guard
Graves flat peg rearsets
Vortex clip ons
Graves Fairing stay
Sharkskinz plastic (repaired and in great shape)
YEC kit ECU (15,900 rev limit-lots of tuning adjustments, temp in speedo)
YEC kit air filter
Modified fuel pump allows tank drain from quick-disconnect fitting
Vortex fuel cap
Vortex frame sliders with shorty pucks & swingarm spools
Vortex Case cover (left)
Factory Pro case cover (right)
Hindle full system with TI can
WERA/CCS safety wired
Stomp-grip
CCS transponder pouch under tail
Michelin PR-3 rear with two sprint races on it
Michelin PR-C front with not much more laps than the rear
Included with the bike are some miscellaneous spares - clip on bars, complete clutch, stock air filter, extra exhaust cans/midpipe, levers, etc.
Available spares include complete set of wheels/rotors/sprocket with Michelin rain tires (slightly used), matching fuel tank complete with cap and pump (no stomp-grip though), matching tail (repaired), air box, new EBC Laser Cut race pads for front, etc.
Bike is located just North of Tampa, FL.
http://www.liquidiq.com/ebay/r6_left.jpg
http://www.liquidiq.com/ebay/r6_front_left.jpg
http://www.liquidiq.com/ebay/r6_front_right.jpg
http://www.liquidiq.com/ebay/r6_right.jpg
http://www.liquidiq.com/ebay/r6_lower_left.jpg
http://www.liquidiq.com/ebay/r6_lower_left_rear.jpg
http://www.liquidiq.com/ebay/r6_right_rear.jpg
http://www.liquidiq.com/ebay/r6_right_lower_rear.jpg
http://www.liquidiq.com/ebay/r6_right_lower_front.jpg
http://www.liquidiq.com/ebay/r6_dash_running.jpg